RainMachine Pro-8 Quick Start Guide
RainMachine Pro-8 Quick-Start Guide
!
Table of Contents
- Inside the box
- Installation
- Fasten the unit
- Electrical Wiring
- Power Up
- Wiring Diagram
- Initial Setup
- Basic Interface
- How It Works
- Operations
- Creating Your First Program
- Suggested vs Custom Duration
- Program Properties
- Watering Zones Manually
- RainMachine mobile app
- Dashboard
- Weather Data
- Restrictions
- Resetting Wi-Fi Settings, Password and data
- Poor Wi-Fi signal strength
- Specifications
- Legal & Warranty
Inside the box
- User Documentation
- RainMachine Pro-8 device (front view)
- 24VAC power adapter (cable 1.5m length)
- 2 drywall screws
- Printed "Quick Start Guide" booklet
Installation
Tip: Take a photo of your old timer wiring for reference!
1. Fasten the unit
Using the provided drywall screws, fasten the unit to the wall at 4 to 5 feet high or eye level.
2. Electrical Wiring
Insert your valve wires into the corresponding terminal. You can use any or all of the “C” terminals as common terminal.
3. Power Up
Connect the power leads to the terminals marked “24VAC” and plug transformer into an AC wall socket. The system will boot up and will enter in the initial setup mode.
Wiring Diagram
3V Battery
24VAC
LAN
F 5V G R C
Rain Sensor Click (optional)
Water source: city or well
Master Valve (Pump)
Flow Sensor (optional)
VALVE 1 ZONE 1
VALVE 2 ZONE 2
VALVE 3 ZONE 3
VALVE 4 ZONE 4
VALVE 5 ZONE 5
VALVE 6 ZONE 6
VALVE 7 ZONE 7
VALVE 8 ZONE 8
F = Flow pulse
5V = optional PWR (Hall type)
G = Ground/Flow pulse
Initial Setup
- Install the RainMachine mobile app on your phone from App Store or Play Store.
- Wire and then power up the RainMachine. (See the wiring diagram from page 5)
- Using your phone go to Settings / Wi-Fi and connect to RainMachine network. Skip this step if you’re using LAN.
- Launch the RainMachine mobile application and continue setup. Enjoy!
Note: If LAN cable is connected to RainMachine, jump to step 4. Make sure your mobile device is connected to the same local Wi-Fi network in order to continue setup.
Basic Interface
After the initial setup is successful you can operate the RainMachine Pro directly from the local interface (Basic Operation).
Note: For advanced settings, you will be required to use the RainMachine mobile app (iOS or Android) or web app located at https://my.rainmachine.com
Wi-Fi
If the Wi-Fi icon is lit, the RainMachine successfully connected to your Wi-Fi or LAN network. If the Wi-Fi icon is OFF or blinking, the unit is indicating an incomplete setup, or no Wi-Fi connection. Tap icon to open RainMachine Pro network status.
Back
Tap on it to go back to the previous screen.
UP and DOWN
Use these buttons to cycle through Zones and Program lists and to change values. When active, the Up and Down buttons will be fully lit.
Water Can
Tap to manually start or stop a zone or a program.
Touch screen
Use Tap action to select options on the screen, like Stop watering a zone, increase or decrease its watering time.
How It Works
Weather-Adaptive Watering
RainMachine programs will dynamically adjust watering duration using Evapotranspiration calculations based on forecast temperature, wind, rain and humidity, sun exposure, etc. In short, we are following environmental conditions, decreasing or increasing water output when necessary.
Operations
Creating Your First Program
In order to enable automatic watering, you need to setup at least one program:
- From the RainMachine app, go to Programs > Add New Program.
- Label your program such as “Rose Garden”.
- Select a Frequency: Determines how often the program runs.
- Set Start Time.
- Choose a base watering duration for each zone (Suggested or Custom).
- Save.
Suggested vs Custom Duration
Watering durations for each programmed zone can be set by: Suggested duration (recommended): Pre-calculated from the properties of your zone (soil type, plant type, sun exposure and location) for a typical summer day. If Weather-Adaptive option is enabled, this duration will be constantly adjusted based on weather.
Custom duration: If you transition from an old controller, you might find it easier to use your previous duration. If Weather-Adaptive option is enabled this duration will be constantly adjusted based on weather.
The RainMachine adjusts these durations based on three weather choices: live, seasonal or “do not adjust”.
Program Properties
Weather-Adaptive Watering: When enabled, the base watering duration (Suggested or Custom) will be adjusted based on weather.
Rain Restriction: Do not water if rain exceeds a certain amount.
Cycle and Soak: Splits the base watering runtime into multiple cycles separated by soak times.
Delay between zones: Sets the amount of time between two consecutive zones in a program, to accommodate specific irrigation systems.
Note: Advanced Program Features are available via RainMachine mobile/web apps.
Watering Zones Manually
From the RainMachine app, go to one of your zones, tap on the play button, and select a desired duration. The UP/DOWN & Water can buttons can be used to achieve the same thing from your RainMachine device.
RainMachine mobile app Dashboard
The dashboard screen allows you to view past and future weather and water consumption statistics. Tap or swipe left/right on each graph to view detailed info.
Weather Data
Settings > Weather: Weather data for your location is fetched several times per day from various weather sources.
Restrictions
Restrictions are a set of rules for the running programs. Example: Specific time spans where no watering takes place.
Freeze Protect
Set a temperature threshold below which watering activity will be stopped.
Hot Days
During hot days increased watering might be required.
Rain and Flow Sensors
A rain or flow sensor can be wired directly to the RainMachine.
Resetting Wi-Fi Settings, Password and data
To change your RainMachine Pro Wi-Fi settings tap on: Wi-Fi button > upper right corner wheel > Change. Follow the on-screen instructions.
To change/reset your RainMachine Pro password tap on Settings > Advanced > Password reset. Open the RainMachine mobile app on your phone to set a new password.
To reset the RainMachine Pro to its factory default settings tap on: Settings > Advanced > Factory reset. After reboot, follow the on-screen wizard steps.
Poor Wi-Fi signal strength
Please consider getting a Wi-Fi signal booster or relocate your Wi-Fi Router or RainMachine.
Specifications
Features
- 8 Zones, Weather Aware, Wi-Fi Irrigation Controller
- Separate Master Valve (Pump) connector
Environmental
- Indoors operating temp: -40C to 60C (-40F to 140F)
Mechanical
- Dimensions: 115 x 115 x 27mm
- Weight: 170g
Electrical
- Wi-Fi: USB 802.11N, 2.4Ghz, US/Japan/EU.
- AC Input: 24VAC, 50/60Hz, 750mA (adapter included).
Certification
- FCC, CE
Warranty
- 1 Year standard warranty
Legal & Warranty
GREEN ELECTRONICS LLC WARRANTS THAT MANUFACTURED EQUIPMENT WILL BE FREE OF ANY DEFECT IN MATERIALS OR WORKMANSHIP FOR THE PERIOD OF 1 YEAR. WARRANTY BEGINS FROM THE DATE OF DELIVERY.